07-11-2007, 23:36
Clarke-Tech Tips & Tricks<
--------------------------------------------------------------------------------
>Secret Menu Clarke-Tech <
Secret Menu:
1)Press 8282 (it will appear the editor for all encryption systems with all the ke*s)
2)Press button mute and then the button exit (it will appear the k*y editor for only the ******* your are watching)
3)Press 8280 (it will appear the B*SS k*y editor)
4)Press mute* exit and then text (it will appear the n*gra boxk*y)
5)Press 8282 and the yellow button (it will appear the n*gra boxk*y)
6)Press 0103 (Reset Pin. The Secure Pin for the menus will be reset. It will be useful if we forget it)
Symbols:
1)Encrypted ******* = € symbol
2)Audio Selection = (stereo* left* right) you will be able to choose one of them pressing the AUDIO button
3)Subtext = you will be able to choose them pressing the AUDIO button
4)Audio Dolby Surround = if it is active you can use the dedicated outlet behind the receiver
Diagonostic Menu:
With the receiver in Stand-By mode:
1)Press and dont leave it the "******* ^" button on the receiver
2)At the same time press the Power-On button on the receiver
It will appear the Diagnostic Menu. When you will reboot the menu it will appear the language selection menu but it seems that you wont loose the other configurations.
If you will active the Diagnostic Menu the receiver will reset the lat and log* so* if you use a rotor and USALS you have to choose the lat and long.
How to activate the Multicas:
1)Go on the Main Menu
2)Go on System Setup and then on Secure Setup
3)Insert the PIN (default PIN is: 0000)
4)You will see MULTICAS* set it on ON mode
or (with old firmwares)
Go on an encrypted ******* and press 6969 and 6969 another time
How to insert the MULT*V*SION AES:
1)Go on a multi*v*sion ******* and press the MUTE button and then EXIT button* it will appear the k*ybox editor of TP*. Insert the first half of the k*y in K*y 01 and the second half in K*y 11. Exit and save.
How to insert the ke*s for XPLUS and INXCT (with bi*s key editor)
1)Go on XPLUS or INXTC *******
2)Open the biss ke* editor (8280) and select one of the key line
3)Write the first part of the key in the line you have choosen
4)Write the second part of the key in the under line
5)Select the first key you have written and press exit.
You will see the *******s. Have fun!
Or:
The same procedure but if you want only XPLUS you can write only the last 8byte of the CW or if you want only INXTC you can write only the first 8bytes of the CW
Manual upgrade for PO*SAT:
1)Go on a PO*SAT ******* and press 8282
2)Go until the 7001 (pol*at provider) and change the ke* 10-11-20-21 with the new ones. Exit and save.
Or (the correct manual procedure):
1)You have to write also the indexes of the provider:
10 + key
11 + key
20 + key
21 + key
so not only the operatives k*ys
it will be useful in the future because not only the 20 and 21 can be changed but also the 10 and 11.
Or:
1)Change in the softcam the ke*s 10 and 11 and write them similar to 20 and 21.
*********
How to insert k*ys for ***View Broadcast (with B*SS ke* editor):
The public keys give light to 5 *******s of ***View Broadcast; they are ***View 247* ***View DP* ***View Plus* ***View Extra and ***View Cum. We can insert these keys in our Clarke-Tech with B*SS ke* editor.
1)Look for a sotfcam with the ke*s for ***View or download for example v_dcw by Mach1
2)Scan 12360H Sr27500 on HotBird 13°E to find the *******s
3)Go on ***View 247 and press 8280 to open the B*SS editor
4)Write on a line the first 8bytes (the first half) of the key for ***View 247
5)Press EXIT and then confim the changes pressing OK. The ******* will be clear.
6)Go on ***View DP and do the same procedure like ***View 247 (obviously using the ke* for ***View DP and writing it on a new line)
7)Go on ***View Plus and now write in the editor the last 8bytes (the second half) of the k*y for ***View Plus. Confirm the changes.
8)Write also the first 8bytes of the k*ys of ***View Extra and ***View Cum on different lines to see them.I hope it will be useful for you.
******************************
Manual upgrade for D+:
a)press 8282 and go on one of D+s *******s* go until the 4001 provider (its the same of 4101)* replace the ke*s with the new indexes 10-11 or 20-21 (it depends on the key* they change) save and exit.
b)the correct procedure is to rewrite the indexes newly:
10+key
11+key
or:
20+key
21+key
so* not only the operatives..
this will be useful in the future* cause not only the 20 and 21 can be changed but also 10 and 11.
c)otherwise* in the softcam* change the 10 and 11 or 20 and 21 ke*s
--------------------------------------------------------------------------------
>Secret Menu Clarke-Tech <
Secret Menu:
1)Press 8282 (it will appear the editor for all encryption systems with all the ke*s)
2)Press button mute and then the button exit (it will appear the k*y editor for only the ******* your are watching)
3)Press 8280 (it will appear the B*SS k*y editor)
4)Press mute* exit and then text (it will appear the n*gra boxk*y)
5)Press 8282 and the yellow button (it will appear the n*gra boxk*y)
6)Press 0103 (Reset Pin. The Secure Pin for the menus will be reset. It will be useful if we forget it)
Symbols:
1)Encrypted ******* = € symbol
2)Audio Selection = (stereo* left* right) you will be able to choose one of them pressing the AUDIO button
3)Subtext = you will be able to choose them pressing the AUDIO button
4)Audio Dolby Surround = if it is active you can use the dedicated outlet behind the receiver
Diagonostic Menu:
With the receiver in Stand-By mode:
1)Press and dont leave it the "******* ^" button on the receiver
2)At the same time press the Power-On button on the receiver
It will appear the Diagnostic Menu. When you will reboot the menu it will appear the language selection menu but it seems that you wont loose the other configurations.
If you will active the Diagnostic Menu the receiver will reset the lat and log* so* if you use a rotor and USALS you have to choose the lat and long.
How to activate the Multicas:
1)Go on the Main Menu
2)Go on System Setup and then on Secure Setup
3)Insert the PIN (default PIN is: 0000)
4)You will see MULTICAS* set it on ON mode
or (with old firmwares)
Go on an encrypted ******* and press 6969 and 6969 another time
How to insert the MULT*V*SION AES:
1)Go on a multi*v*sion ******* and press the MUTE button and then EXIT button* it will appear the k*ybox editor of TP*. Insert the first half of the k*y in K*y 01 and the second half in K*y 11. Exit and save.
How to insert the ke*s for XPLUS and INXCT (with bi*s key editor)
1)Go on XPLUS or INXTC *******
2)Open the biss ke* editor (8280) and select one of the key line
3)Write the first part of the key in the line you have choosen
4)Write the second part of the key in the under line
5)Select the first key you have written and press exit.
You will see the *******s. Have fun!
Or:
The same procedure but if you want only XPLUS you can write only the last 8byte of the CW or if you want only INXTC you can write only the first 8bytes of the CW
Manual upgrade for PO*SAT:
1)Go on a PO*SAT ******* and press 8282
2)Go until the 7001 (pol*at provider) and change the ke* 10-11-20-21 with the new ones. Exit and save.
Or (the correct manual procedure):
1)You have to write also the indexes of the provider:
10 + key
11 + key
20 + key
21 + key
so not only the operatives k*ys
it will be useful in the future because not only the 20 and 21 can be changed but also the 10 and 11.
Or:
1)Change in the softcam the ke*s 10 and 11 and write them similar to 20 and 21.
*********
How to insert k*ys for ***View Broadcast (with B*SS ke* editor):
The public keys give light to 5 *******s of ***View Broadcast; they are ***View 247* ***View DP* ***View Plus* ***View Extra and ***View Cum. We can insert these keys in our Clarke-Tech with B*SS ke* editor.
1)Look for a sotfcam with the ke*s for ***View or download for example v_dcw by Mach1
2)Scan 12360H Sr27500 on HotBird 13°E to find the *******s
3)Go on ***View 247 and press 8280 to open the B*SS editor
4)Write on a line the first 8bytes (the first half) of the key for ***View 247
5)Press EXIT and then confim the changes pressing OK. The ******* will be clear.
6)Go on ***View DP and do the same procedure like ***View 247 (obviously using the ke* for ***View DP and writing it on a new line)
7)Go on ***View Plus and now write in the editor the last 8bytes (the second half) of the k*y for ***View Plus. Confirm the changes.
8)Write also the first 8bytes of the k*ys of ***View Extra and ***View Cum on different lines to see them.I hope it will be useful for you.
******************************
Manual upgrade for D+:
a)press 8282 and go on one of D+s *******s* go until the 4001 provider (its the same of 4101)* replace the ke*s with the new indexes 10-11 or 20-21 (it depends on the key* they change) save and exit.
b)the correct procedure is to rewrite the indexes newly:
10+key
11+key
or:
20+key
21+key
so* not only the operatives..
this will be useful in the future* cause not only the 20 and 21 can be changed but also 10 and 11.
c)otherwise* in the softcam* change the 10 and 11 or 20 and 21 ke*s
